LED Boost Gauge With Optional Programmable Peak Hold ^tm

Install Your Own Custom In-Dash 20 Indicator 20, 25 or 30 PSI Boost Gauge (Any Car)

In Dash PSI Boost Gauge Kit With Optional "Peak hold" (Any Vehicle Version, Utilizes External Boost Sensor)

The kit includes everything you need in order to build your own accurate (+/-  0.250 PSI) fully functional turbo boost gauge. It takes the signal from a supplied Computer Grade pressure sensor and monitors the boost pressure "Real Time".  Results are reported on 20 LED indicators with an accuracy of approximately +/- 0.250 of a PSI when installed and setup correctly. For a 20psi gauge each indicator equals 1psi. For 25psi each indicator equals 1.25psi and for 30psi each indicator equals 1.5psi.

The Programmable Peak Hold ^tm Option is available on request. It includes user selectable modes configured with an external switch, potentiometer and/or a fixes resistor. A single indicator remains on for a programmed amount of time indicating the Peak Boost Pressure reached. If a higher boost is recorded before it is reset it moves to the higher reading. Spikes can easily be monitored and boost peaks tracked efficiently.

Programmable Peak Hold Modes Available:

• Indefinite Delay/Decay (Peak hold remains on for a long time before slowly decaying)

• Pre-Set Delay/Decay (Peak hold remains on for a fixed time before decaying)

• Variable Delay/Decay (Peak hold is adjustable via an external potentiometer)

• Reset (Peak hold is reset to zero by an external switch)

• No Peak Hold (Peak hold feature is switched off by an external switch)

Indicator colors can be customized in any combination of Red, Green, Yellow, Amber & Blue.

Sample Installation - Boost Gauge Installed in Stock Instrument Cluster - Click on photo for Video
 

The unit also includes custom "Dimmer" technology that automatically dims the indicators for night time driving to an adjustable pre-set level,  when you turn on your car's master light switch. The night time brightness can be adjusted to suite individual requirements.

An accurate "Real Time" boost gauge is an absolute must, especially if you have done any non stock performance upgrades to your car. Such as; installing a new chipped ECU, increasing turbo boost settings, adding boost controllers etc.  Calibration is easy to do and default components are provided for sea level operation. The circuit is flexible enough to be configured for any altitude if needed. You can mount the Indicators anywhere you like. But we recommend putting them in the existing tachometer dial in your car's instrument cluster.  This is not too difficult to do and is discussed in detail in a dedicated articles on this web site under specific vehicles.  Yes, they can be fitted right into the car's dash board. Custom Dash Drilling Templates are available on request. The control unit is so small it can easily be concealed behind the dash.
 

• Digital Boost Gauge Kit, Ready Built & Tested Control Unit & Loose LEDs ($225 - Group Discounts Available)
   

This kit includes the following: 

• 1 completed, calibrated and tested Digital Boost Control Unit (DBCU) with "Dimmer" technology

• 1 Instrument Grade MAP Sensor

• 20 Loose indicators in the colors of your choice Red, Green, Yellow, Amber & Blue. (Blue Indicators are $4 extra each)

• Female Power Connector with pre-wired Loom

• Generic installation and operational instructions

Additional items that may be required: 

• Compact Black Enclosure

• You will need some good soldering and general DIY skills in order to complete this project

• Drill & Drill Press

• Fine tipped low Wattage soldering iron & solder

• About 25 feet of 28 SWG LED hookup wire

• Miscellaneous pieces of wire

All you have to do to complete the project is install the Indicators in your dash or any other desired location, wire them up to the PCB, connect the power, dimmer wire to the light switch and connect 1 1/8" NPT pipe from your vacuum line to the provided MAP sensor, and you are ready to go.

Boost Gauge Main Control Unit, & LED Indicator Options, Not To Scale

Boost Gauge Main Control Unit, PCB Layout & Wiring Diagram, Not To Scale

• NEW Generation 6 "State of the Art" Silk Screened PCB

This is the LATEST IMP Concepts streamlined PCB design. Features the highest quality materials for exceptional features and reliability.

• Programmable Peak Hold ^tm Option ($50)

Posted prices do not include the Programmable Peak Hold Option. External Potentiometer, Fixed Resistors and switch are sold separately or can be provided by the user.
 

Suggested "Programmable Peak Hold " Switch Wiring:

Example In-Dash Installation Options, the Color & Styles can be Customized to Taste

To Check Out an Installation Of This Gauge, Click Here and Select The Project You Wish To View!

Payment Methods:

PAYPAL and Money Orders are the ONLY method of payment accepted. Please use PAYPAL to pay with your credit card.